DIY Paint Drying Rack! {and more resin adventures!}

Happy Monday folks! It looks like today is going to be sunny and hot, a perfect day for the beach…or to play with resin some more…or better yet both! I can make some resin stuff and escape the fumes and the temptation to bother it as it cures LOL! this weekend I used up the last of the big pint can of resin i bought and you know what? I really enjoyed the process of learning about it, so much so in fact I took my 50% off coupon to ACmoore yesterday and bought the even bigger quart can of it LOL! I was going to try the epoxy kind but they were sold out at both craft stores and I was not letting the 50% off coupon go to waste:) I learned something new this weekend about polyester resin, well several things actually but before we get into that I wanted to show you the drying rack I built for holding glazed or painted objects:

DCF 1.0

The photo is self explanatory but basically I took 2 scraps of foam-core and glued them together then inserted sewing pins every 3/4″ or so. I think I might make one with the pins closer together to hold jewelry parts too! Maybe I’ll make a video but you’re pretty bright so I’m sure you get the gist. πŸ˜€

EDIT: I decided I wanted a board with the pins closer together for glazing jewelry components so I made a video, enjoy!

Resin Tip #25 Always use Mold Release!

While making my sea glass paper weights above I was impatient and did not prep the soap molds I used with mold release. Now there is a chance that the molds were the wrong kind of plastic but every kind of plastic I have used before have worked (even candy molds!) with mold release. The downside is that you have to plan ahead of time and spray the molds and let them dry, I’m not big on planning Β so since I had 2 of that particular soap mold I through caution to the wind…

DCF 1.0

Yep, bad idea.

Resin Tip #26: Use a heat gun to remove the stuck on plastic mold from your resin.

I was not about to let my resin paper weights go in the trash just yet so I cut apart the plastic mold and tried to bread the plastic off, not happening. So I grabbed my heat gun and heated the plastic and peeled it off. By the way I had the door open and 3 fans on during this unwise fume fest. I was able to pull most of the plastic off BUT the was still some bits of plastic stuck to the edges so I began sanding, first with a rough paper to remove the plastic then with a finer sponge to polish it. Please use a dust mask or respirator if you do this. That removed the plastic but let my paperweights dull and lifeless. We can’t have that now can we? so I grabbed my trusty Future Floor Wax with Pledge Shine (which has never seen a floor BTW) and gave them a shiny new glaze. It worked, dried rock hard and quickly! Yay! I needed to glaze all sides so did the bottom first, placed it on my drying rack and glazed the top and sides. After seeing how well that worked I glazed my green jewelry pieces from the other day. It got rid of the slightly tackiness of the ones done in silicone and it made the bits I had to file and smooth on the circle pendants disappear. It made my grimy fingerprints go away too and left shiny goodness in their place! Huh, I wonder how that stuff works on floors?

I also learned that larger pieces cast quicker with polyester resin. It was a dry 75 degree day when I made the paper weights and other items (I made sea glass embedded pendants and charms for earrings) and after pouring I took the molds outside and put them in the sun and covered them with a clear plastic tote. The paperweights were hot in the molds before I even went out and they were cured in a few hours while the pendants were still a bit tacky. The heat is key I think because you have to use 3 times the amount of hardener in the 1/8″ thick items as the 3/4″ items and each layer if resin requires less hardener if you are layering stuff. I also learned that you can color resin with dye reinkers for transparent items or acrylic paint for an opaque look. I have lots of both so that saves me money on specialty colorants!

I hope you found today’s post useful. Even if you never want to try resin after reading my adventure at least you can make a nifty paint drying rack for other projects like Christmas ornaments or tole painting projects. Β Well, I am off to the beach today, maybe I can find some more sea glass or other treasures to bring back. Thanks for stopping by and til next time happy crafting!

13 thoughts on “DIY Paint Drying Rack! {and more resin adventures!}

  1. Nice! I have to paint a load of washers this week for a crafty girls birthday party this coming weekend. we will be making washer necklaces. I want to get the base paint done ahead of time and I’ve been racking my brain for a good way to dry the washers without having to sand edges. I was going to brush paint them to prevent them getting stuck to a surface, but I think I can just build this rack and use it to hold them for painting and drying! Thank you!!!! You just saved me a lot of time and aggravation!


  2. Great paperweights Lindsay…don’t think I will be trying resin anytime soon, but enjoyed learning a bit about it from ‘The Frugal Crafter’!!! TFS
    Paper Hugs,


  3. I think I have enough projects on the go so I’ll stay away from resin. I wonder if you use push pins instead of straight pins and place them a little farther apart would your items be more stable on the wider surface?


  4. Great idea for a drying rack! Do you have to glaze/paint one side at a time or are the pin heads small enough they won’t mess up the back if you put something down on it still wet? (Can you tell I tend to be impatient?)


  5. Hey Lindsay, I watched a bunch of Youtube video’s the other night about resin molds and the ladies were all using common baby powder as mold release…of course they were using clay for the most part to make their cast so perhaps that wouldn’t work for a liquid cast like resin. Hmmm, no I think one lady also used liquid resin in a clay mold(you know, the kind of molds you make yourself with the two parts of clay that set up or you can bake them to set up?) with baby powder as a release. Perhaps you can only use the baby powder as a release with clay molds…? Okay, so not as helpful as I meant to be, still. πŸ™‚


  6. I don’t know if this will work with resin, but when I do plaster molds I use hand dish washing soap right out of the bottle. It works just like the mold soap that is used as a release agent. If you don’t like doing dishes by hand, you are bound to have lots of it around (like I do) πŸ™‚


    1. hahaha surprisingly I have a lot of that hanging around too, hmmmm…I actually have the proper mold release, I just forgot to prep that mold:)


Tell me what YOU think!

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.